শিপল্যাপ ক্যালকুলেটর
মাল্টি-ওয়াল সুবিধা, নিখুঁত ওভারল্যাপ এবং 2D লাইভ লেআউট ভিজ্যুয়ালাইজার সহ প্রফেশনাল কাঠের হিসাব।
1 দেয়ালের পরিমাপ
ইম্পেরিয়াল: ফুট ও ইঞ্চি2 দরজা ও জানালা (বাদ দেওয়া ক্ষেত্রফল)
অতিরিক্ত কাঠ কেনা এড়াতে দরজা, জানালা ও ফায়ারপ্লেসের মাপ বাদ দিন।
No openings added. (Full wall area calculated)
3 তক্তার প্রোফাইল ও খাঁজের ধরন
4 দিক, কাঠামোর দূরত্ব ও অপচয়
প্রয়োজনীয় নির্মাণ সামগ্রী
*Planning Disclaimer: Fastener counts, adhesive tubes, and cost estimates are rules of thumb for planning purposes. Verify exact counts and local building codes prior to purchasing.
শিপল্যাপ কী এবং ওভারল্যাপ কেন গুরুত্বপূর্ণ?
আসল শিপল্যাপে উভয় প্রান্তে বিশেষ খাঁজ (র্যাবেট) কাটা থাকে। বসানোর সময় একটির খাঁজ অন্যটির উপর বসে একটি জলরোধী স্তর এবং সুন্দর ছায়ারেখা তৈরি করে।
যেহেতু প্রতিটি তক্তা আধা ইঞ্চি ওভারল্যাপ করে, তাই দেয়ালে দৃশ্যমান অংশ তক্তার মোট প্রস্থের চেয়ে কম হয়।
Stainable, natural grain, interior accent walls
Ultra-smooth, zero knots, budget painted walls
Moisture & rot resistant, siding & baths
100% waterproof for showers & wet siding
প্রোফাইল ও ওভারল্যাপ সিমুলেটর
যেকোনো দেয়াল বা সিলিংয়ের জন্য কাঠের হিসাবের ৫টি ধাপ
কাঠমিস্ত্রিদের পরীক্ষিত ৫টি নিয়ম। সূত্র ও নকশা দেখতে প্রতিটি ধাপে ক্লিক করুন।
Measure Gross Wall Dimensions
Measure the total width and height of each wall in feet and inches. Multiply Width × Height to establish the total gross square footage before deductions.
কক্ষভিত্তিক কাঠের কাজের নির্দেশিকা
অগ্নি নিরাপত্তা নিয়ম, আর্দ্রতা সুরক্ষা এবং সঠিক ফাস্টেনার দেখতে যেকোনো রুম নির্বাচন করুন।
Fireplace Accent Walls & TV Surrounds
National Fire Protection Association (NFPA 211) mandates a minimum 6-inch non-combustible setback (stone, tile, or cement backerboard) between the fireplace firebox opening and combustible wood shiplap. For gas or electric fireplaces, consult manufacturer zero-clearance specs before installing.
নামমাত্র বনাম আসল কাঠের মাপের তুলনা
কাঠ কাটার আগের মাপে নাম রাখা হয়। ইন্টারঅ্যাক্টিভ ক্যালিপার দেখতে প্রোফাইলে ক্লিক করুন।
5⅜" Actual Width • 4⅞" Exposed Face
Planed down to 5.375" actual width. The ½" rabbet joint reduces exposure to 4.875", creating the benchmark American farmhouse look.
| Nominal Size | Actual Width | Overlap | Exposed Face | Coverage (8ft) | Boards / 100 sq ft | Best Application |
|---|---|---|---|---|---|---|
| 1×4 | 3.500" | 0.500" | 3.000" | 2.00 sq ft | 50 | Wainscoting, mudrooms, compact bathrooms |
| 1×6 | 5.375" | 0.500" | 4.875" | 3.25 sq ft | 31 | Standard accent walls, fireplaces, most popular |
| 1×8 | 7.250" | 0.500" | 6.750" | 4.50 sq ft | 23 | High ceilings (9ft–12ft), master bedrooms, exteriors |
| 1×10 | 9.250" | 0.500" | 8.750" | 5.83 sq ft | 18 | Grand open living rooms, barn conversions, rustic |
| 1×12 | 11.250" | 0.500" | 10.750" | 7.17 sq ft | 14 | Two-story foyers, commercial lobbies, modern wide-plank |
পেরেক দৈর্ঘ্য ও কাঠামোর গভীরে প্রবেশের সিমুলেটর
কাঠ বাঁকা হওয়া রোধ করতে ফ্রেমে কমপক্ষে ২৫ মিমি (১ ইঞ্চি) পেরেক প্রবেশ করা আবশ্যক।
Adjust Framing & Fastener Length
Finish Nails
Optimal holding strength for solid wood planks without splitting thin tongue profiles.
Brad Nails
Leaves tiny holes for quick wood filler touch-up. Always combine with construction adhesive.
304 / 316 Fasteners
Mandatory for outdoor shiplap and cedar siding to prevent black tannin rust staining.
Worked Example: 12' × 8' Wall with 2 Windows
Here is the exact mathematical step-by-step trace our calculator performs so you can verify the results by hand.
Given Parameters:
কাঠের প্রকারভেদ ও মজুরি খরচের গাইড
কাঠের ধরন অনুযায়ী খরচ ভিন্ন হয়। সামগ্রিক বাজেট জানতে সিমুলেটরটি ব্যবহার করুন।
Calculate Total Room Budget
| Wood Species / Material | Material ($/sq ft) | 100 sq ft DIY | 100 sq ft Installed | Recommended Usage |
|---|---|---|---|---|
| Primed MDF Shiplap | $1.50 – $2.25 | $200 – $275 | $450 – $675 | Interior painted accent walls, budget remodels |
| Pine / SPF (Knotty) | $2.20 – $3.50 | $270 – $400 | $520 – $800 | Rustic stained walls, farmhouse look |
| Poplar / Select Pine | $3.75 – $5.00 | $425 – $550 | $675 – $950 | High-end smooth painted finishes, zero knot bleed |
| Western Red Cedar | $5.50 – $8.50 | $600 – $900 | $850 – $1,300 | Exterior siding, bathrooms, covered porches |
| Cellular PVC / Composite | $5.00 – $7.50 | $550 – $800 | $800 – $1,200 | 100% waterproof exterior, zero maintenance |
| Reclaimed Barn Wood | $8.00 – $14.00 | $850 – $1,450 | $1,100 – $1,850 | Authentic rustic texture, vintage character |
কাটিং অপচয় ও প্যাকেট রাউন্ডিং সিমুলেটর
জানুন কেন ৪০ সেমি-র নিচের টুকরো ফ্রেমে লাগানো যায় না এবং আপনার সেফটি মার্জিন ঠিক করুন।
Simulate Board Cuts on 16" Studs
Simple Rectangular Walls
Standard interior accent walls with 1 or zero openings only generate 5–8% real offcut waste. Adding a 10% factor ensures you have spare boards to cull knot defects.
Ceilings, Bathrooms & Siding
Ceilings and walls with multiple windows require frequent end cuts around trim and light fixtures. An extra 15% allowance prevents mid-project supply runs.
Diagonal & Herringbone
Diagonal 45-degree installations create triangular cutoffs at every wall edge. Triangular offcuts cannot be flipped over because the rabbet groove face is reversed.
16" Stud Span Rule
Offcuts shorter than 16 inches cannot span across two wall framing studs and must be discarded as scrap.
Retail Pack Rounding
Shiplap is sold in 6-board bundles. Always round up to full bundles to avoid lot-matching color variations.
Natural Lumber Culling
Real wood bundles contain 3–5% bowed planks or loose knot holes that should be culled before installation.
রং সিমুলেটর ও সিলিং ম্যাপ
জনপ্রিয় রং পরীক্ষা করুন এবং ফাঁটা রোধ করতে কোথায় সিলিকন লাগাতে হবে তা জানুন।
Select Finish & Color
Best all-round designer finish. Provides clean shadow gap contrast with easy wipe-down durability.
Pre-Paint Tongue Lips
Always prime and paint rabbet grooves before nailing. Prevents unpainted wood strips from appearing during winter wood shrinkage.
Knot Bleed Sealer
Apply a shellac-based primer over pine knot clusters to prevent yellow resin tannin bleed-through on white paint.
Satin Sheen Advantage
Satin enamel balances soft architectural shadow lines with wipe-down washability for long-term durability.
শিপল্যাপ বনাম নিকেল গ্যাপ বনাম টি অ্যান্ড জি বনাম বোর্ড অ্যান্ড ব্যাটেন
ক্রস-সেকশন চিত্রসহ ৪টি কাঠের ক্ল্যাডিং সিস্টেমের তুলনামূলক বিশ্লেষণ।
Opposing Rabbet Overlap Joints
Milled with matching ½-inch L-shaped steps on opposite edges. Boards rest over each other to form a tight, overlapping moisture barrier with subtle rustic character.
| Feature | Standard Shiplap | Nickel Gap | Tongue & Groove (T&G) | Board & Batten |
|---|---|---|---|---|
| Joint Design | Opposing Rabbets (½" lap) | T&G with ⅛" reveal built-in | Interlocking Tongue & Groove | Flat boards + vertical battens |
| Shadow Gap | Tight flush or slight bevel | Crisp ⅛" intentional shadow | V-groove or flush bead | High-relief 3D batten projection |
| Water Shedding | Superior (overlapping shingle action) | Good (exterior siding certified) | Excellent (tight interlock) | Good (caulk battens on siding) |
| Blind Nailing | Yes (45° nail through top lip) | Yes (through tongue shoulder) | Yes (100% concealed fastener) | No (face-nailed battens) |
| Avg Material Cost / sq ft | $2.00 – $4.50 | $2.50 – $5.00 | $2.25 – $4.75 | $1.75 – $3.50 |
| Installation Difficulty | Beginner / DIY friendly | Beginner / Fast alignment | Intermediate (tight seating) | Beginner (simple square cuts) |
কোণা, স্কার্টিং ও সুইচবোর্ড এক্সটেন্ডার
নিখুঁত ফিনিশিং-ই সেরা কাজের পরিচয়। বিস্তারিত আর্কিটেকচারাল নকশা দেখুন।
Square 1×1 Backer Corner Block
Install a square 1×1 or 1×2 wood corner cleat vertically in the inside drywall corner first. Butt your horizontal shiplap boards directly against this cleat for clean square terminations.
Inside Corners
Butt joint with 1×1 corner cleat, or caulk a tight butt joint with paintable acrylic.
Outside Corners
Precision 45° miter cuts glued with CA glue, or cover with an L-shaped solid corner moulding.
Door & Window Casings
Install casings that are at least 1/8" thicker than shiplap (minimum 3/4" to 1" casing).
Electrical Outlets
NEC 314.20 requires non-conductive box extender rings to bring outlets flush with wood face.
Interior Accent Walls vs. Exterior Siding Rules
Exterior shiplap requires specialized weather-resistive barriers, drainage gaps, and corrosion-resistant fasteners.
Interior Installation Protocol
Living rooms, bedrooms, ceilings- ✓ Direct Drywall Install: Nail directly into wall framing studs with 16ga/18ga brads.
- ✓ Adhesive Boost: Apply construction adhesive in an S-bead pattern on every board.
- ✓ Acclimation: Store wood inside the room for 48 to 72 hours prior to nailing.
Exterior Siding Protocol
Exterior cladding, sheds, porches- ✓ House Wrap WRB: Must have a continuous Weather-Resistive Barrier before boards.
- ✓ Stainless Steel Nails: Always use 304/316 stainless ring-shank nails outdoors.
- ✓ Lapping Direction: Always install horizontal siding starting from the bottom upward.
সিলিং উচ্চতা অনুযায়ী তক্তার প্রস্থ সিমুলেটর
তক্তার প্রস্থ ঘরের দৃষ্টিগত উচ্চতা পরিবর্তন করে। বিভিন্ন অনুপাত যাচাই করুন।
8-Foot Ceiling Proportions
In standard 8ft ceilings (96 inches), 1×6 shiplap (4.875" reveal) creates exactly 20 horizontal courses, producing the classic balanced farmhouse proportion without feeling overcrowded.
Small Spaces & Powder Rooms
Best for cozy powder rooms, laundry rooms, entryways, and historic Victorian restorations where smaller repeating lines add texture without overpowering small spaces.
Industry Standard Benchmark
The industry benchmark. Accounts for over 70% of residential accent walls because it balances visual weight perfectly in rooms between 8ft and 10ft ceiling heights.
Great Rooms & High Ceilings
Wider boards visually stretch walls horizontally, making large living rooms and high entries feel grounded and architecturally refined.
ইন্টারঅ্যাক্টিভ কোয়ালিটি কন্ট্রোল চেকলিস্ট
নিখুঁত কাজের জন্য সম্পন্ন হওয়া কাজগুলো টিক দিন।
Frequently Asked Questions
Answers to the most common questions about shiplap calculation, joinery math, and installation techniques.
ইন্টারঅ্যাক্টিভ কার্পেন্ট্রি ও মিলওয়ার্ক শব্দকোষ
বর্ণানুক্রমে ফিল্টার করুন অথবা কাঠমিস্ত্রির কারিগরি শব্দ খুঁজুন।
Acclimation
The mandatory process of storing unfinished wood boards inside the installation room for 48 to 72 hours so internal moisture content balances with ambient humidity.
Blind-Nailing
Driving a finish nail at a 45-degree angle through the upper tongue or rabbet lip so the fastener head is completely concealed by the next overlapping board course.
Board & Batten
A traditional siding or wall cladding system consisting of wide vertical planks with narrow vertical wood battens covering the seams between planks.
Box Extender Ring
A non-conductive plastic or metal extension sleeve fitted inside existing electrical outlet/switch boxes to bring receptacle faces flush with wood wall coverings (NEC 314.20).
Caulking
Applying flexible acrylic latex sealant to inside corners, window casings, and baseboards to seal perimeter transitions before painting.
Course
A single continuous horizontal (or vertical) row of shiplap boards spanning across a wall or ceiling.
Exposed Face
The visible finished surface width of a shiplap board once it is installed and overlapping with adjacent boards. Nominal 1×6 has a 4.875" exposed face.
Furring Strips
Narrow wood battens (typically 1×3 or 2×2) fastened to masonry, basement concrete, or uneven drywall to create a level, plumb framing grid for shiplap nails.
Linear Feet (LF)
The total length of lumber boards laid end-to-end in feet, calculated by dividing required board area by exposed board width in feet.
MDF (Medium Density Fiberboard)
An engineered wood product made of wood fibers glued under high pressure. Highly dimensionally stable with ultra-smooth paint surfaces, but vulnerable to liquid water.
Nickel Gap
A contemporary cladding profile featuring an intentional 1/8-inch (thickness of a US nickel) shadow reveal between boards with straight vertical shoulders.
Nominal vs. Actual
The difference between rough lumber naming (e.g. 1×6) and the actual planed dimensions after sawmill drying (0.688" × 5.375").
Rabbet Joint
An L-shaped step or recess cut along the edge of a wood board. Standard shiplap features two opposing rabbets that overlap.
Tongue & Groove (T&G)
An interlocking wood joint system where a protruding ridge (tongue) on one board fits tightly into a matching groove on the adjoining board.
Wainscoting
Wooden wall paneling covering the lower one-third to one-half of an interior wall, traditionally capped with a chair rail and baseboard.
No matching carpentry terms found
Try searching for shiplap, rabbet, nail, overlap, or board dimensions.
Add This Shiplap Calculator to Your Website
Give your readers an interactive, instant calculation tool. Clean, responsive, and 100% free with a simple one-line embed code.
Thomas is a licensed finish carpenter and architectural woodworker with over 18 years of experience framing and installing interior millwork. Formulas audited against AWCI and standard NWFA milling standards.